Tolerance analysis of overconstrained and flexible assemblies by polytopes and finite element computations: application to a flange
dc.contributor.author | GOUYOU, Doriane | |
dc.contributor.author | LEDOUX, Yann
IDREF: 102217890 | |
dc.contributor.author | TEISSANDIER, Denis | |
dc.contributor.author | DELOS, Vincent | |
dc.date.accessioned | 2021-05-14T09:51:05Z | |
dc.date.available | 2021-05-14T09:51:05Z | |
dc.date.issued | 2017 | |
dc.identifier.issn | 0934-9839 | |
dc.identifier.uri | https://oskar-bordeaux.fr/handle/20.500.12278/77348 | |
dc.description.abstractEn | In industrial contexts, overconstrained assemblies are often used to ensure sufficient stiffness and accuracy of assembly. Such architectures are quite usual, however , analysis and synthesis of the tolerance are not easy to define and quantify. In these cases, the compliance of the assembly is not automatic and deformations may often occur, requiring a particular and difficult analysis of the assembly from scientific and computing points of view. The present work addresses such overconstrained mechanisms through a general and a sequential approach. Based on this, it is possible to determine the final assembly condition (with or without interference) as a function of part defects. First, the assembly procedure is performed based on polytope computations, assuming a rigid part behavior. From this, a stochastic simulation is performed and some non-compliant assemblies (assemblies with interferences) are identified. For these assemblies, the rigid behavior of parts is then overcome by means of finite element simulations and a typical procedure is set up to introduce part defects. We then deduce whether the assembly can be made from the load needed to assemble the parts. This procedure is applied to a flange composed of five pin / hole pairs, as this is a highly overconstrained mechanism. | |
dc.language.iso | en | |
dc.publisher | Springer Verlag | |
dc.subject.en | Overconstrained mechanism | |
dc.subject.en | Tolerance analysis | |
dc.subject.en | Interferences | |
dc.subject.en | Flexible assembly | |
dc.subject.en | Polytopes | |
dc.title.en | Tolerance analysis of overconstrained and flexible assemblies by polytopes and finite element computations: application to a flange | |
dc.type | Article de revue | |
dc.identifier.doi | 10.1007/s00163-017-0256-5 | |
dc.subject.hal | Informatique [cs]/Logiciel mathématique [cs.MS] | |
dc.subject.hal | Sciences de l'ingénieur [physics]/Mécanique [physics.med-ph] | |
bordeaux.journal | Research in Engineering Design | |
bordeaux.hal.laboratories | Institut de Mécanique et d’Ingénierie de Bordeaux (I2M) - UMR 5295 | * |
bordeaux.institution | Université de Bordeaux | |
bordeaux.institution | Bordeaux INP | |
bordeaux.institution | CNRS | |
bordeaux.institution | INRAE | |
bordeaux.institution | Arts et Métiers | |
bordeaux.peerReviewed | oui | |
hal.identifier | hal-01515475 | |
hal.version | 1 | |
hal.origin.link | https://hal.archives-ouvertes.fr//hal-01515475v1 | |
bordeaux.COinS | ctx_ver=Z39.88-2004&rft_val_fmt=info:ofi/fmt:kev:mtx:journal&rft.jtitle=Research%20in%20Engineering%20Design&rft.date=2017&rft.eissn=0934-9839&rft.issn=0934-9839&rft.au=GOUYOU,%20Doriane&LEDOUX,%20Yann&TEISSANDIER,%20Denis&DELOS,%20Vincent&rft.genre=article |
Files in this item
Files | Size | Format | View |
---|---|---|---|
There are no files associated with this item. |