Mostrar el registro sencillo del ítem

Comparison between cryogenic coolants effect on tool wear and surface integrity in finishing turning of Inconel 718

hal.structure.identifierLaboratoire Angevin de Mécanique, Procédés et InnovAtion [LAMPA]
hal.structure.identifierMondragon Unibertsitatea
dc.contributor.authorCHAABANI, Sana
hal.structure.identifierMondragon Unibertsitatea
dc.contributor.authorARRAZOLA, Pedro José
hal.structure.identifierLaboratoire Angevin de Mécanique, Procédés et InnovAtion [LAMPA]
dc.contributor.authorAYED, Yessine
hal.structure.identifierMondragon Unibertsitatea
dc.contributor.authorMADARIAGA, Aitor
hal.structure.identifierLaboratoire d'Etude des Microstructures et de Mécanique des Matériaux [LEM3]
dc.contributor.authorTIDU, Albert
hal.structure.identifierLaboratoire Angevin de Mécanique, Procédés et InnovAtion [LAMPA]
dc.contributor.authorGERMAIN, Guénaël
dc.date.accessioned2021-05-14T09:32:43Z
dc.date.available2021-05-14T09:32:43Z
dc.date.issued2020-11
dc.identifier.issn0924-0136
dc.identifier.urihttps://oskar-bordeaux.fr/handle/20.500.12278/75987
dc.description.abstractEnThe most important challenges when machining difficult-to-cut alloys used in critical applications consist mainly in increasing tool life as well as improving the component surface integrity. In particular, the nickel based alloys exhibit very low thermal conductivity inducing higher cutting temperature and thereby rapid tool wear. In this context, cryogenic machining is a promising approach that enhances cooling efficiency either when using the liquid nitrogen LN2 or the carbon dioxide LCO2. According to previous works, cryogenic machining has been carried out on several work materials such as titanium alloys and nickel based alloys. Their findings figured out that longer tool life and better surface integrity were obtained when machining titanium alloys, unlike nickel based alloys. In this work, a comparative study has been carried out in order to investigate the cryogenic machining performance during turning operation of Inconel 718 with respect to tool wear behavior and surface integrity of the machined part. In fact, two cryogenic fluids were employed namely LN2 and LCO2 considering as a reference the conventional lubrication. This study illustrates that conventional lubrication and LCO2 cryogenic cooling allowed to obtain similar machining time, tool wear and surface finish. Nevertheless, LN2 cryogenic machining resulted in the lowest tool life as well as the poorest surface finish. Moreover, residual stresses have been measured beneath the machined surfaces when machining using new tools and tools with different levels of tool flank wear. It was observed that compared to conventional lubrication, both cryogenic conditions showed better results with respect to residual stress profiles along the machined surfaces
dc.language.isoen
dc.publisherElsevier
dc.subject.enCeramics and Composites
dc.subject.enMetals and Alloys
dc.subject.enIndustrial and Manufacturing Engineering
dc.subject.enModelling and Simulation
dc.subject.enComputer Science Applications
dc.subject.enCryogenic machining
dc.subject.enInconel 718
dc.subject.enSurface integrity
dc.subject.enTool wear
dc.title.enComparison between cryogenic coolants effect on tool wear and surface integrity in finishing turning of Inconel 718
dc.typeArticle de revue
dc.identifier.doi10.1016/j.jmatprotec.2020.116780
dc.subject.halSciences de l'ingénieur [physics]/Mécanique [physics.med-ph]/Génie mécanique [physics.class-ph]
bordeaux.journalJournal of Materials Processing Technology
bordeaux.page116780
bordeaux.volume285
bordeaux.hal.laboratoriesInstitut de Mécanique et d’Ingénierie de Bordeaux (I2M) - UMR 5295*
bordeaux.institutionUniversité de Bordeaux
bordeaux.institutionBordeaux INP
bordeaux.institutionCNRS
bordeaux.institutionINRAE
bordeaux.institutionArts et Métiers
bordeaux.peerReviewedoui
hal.identifierhal-02972763
hal.version1
hal.origin.linkhttps://hal.archives-ouvertes.fr//hal-02972763v1
bordeaux.COinSctx_ver=Z39.88-2004&rft_val_fmt=info:ofi/fmt:kev:mtx:journal&rft.jtitle=Journal%20of%20Materials%20Processing%20Technology&rft.date=2020-11&rft.volume=285&rft.spage=116780&rft.epage=116780&rft.eissn=0924-0136&rft.issn=0924-0136&rft.au=CHAABANI,%20Sana&ARRAZOLA,%20Pedro%20Jos%C3%A9&AYED,%20Yessine&MADARIAGA,%20Aitor&TIDU,%20Albert&rft.genre=article


Archivos en el ítem

ArchivosTamañoFormatoVer

No hay archivos asociados a este ítem.

Este ítem aparece en la(s) siguiente(s) colección(ones)

Mostrar el registro sencillo del ítem