Mostrar el registro sencillo del ítem

hal.structure.identifierEuropean Institute For Energy Research [EIFER]
dc.contributor.authorDAILLY, Julian
hal.structure.identifierEuropean Institute For Energy Research [EIFER]
dc.contributor.authorMARRONY, Mathieu
hal.structure.identifierInstitut Charles Gerhardt Montpellier - Institut de Chimie Moléculaire et des Matériaux de Montpellier [ICGM ICMMM]
dc.contributor.authorTAILLADES, Gilles
hal.structure.identifierInstitut Charles Gerhardt Montpellier - Institut de Chimie Moléculaire et des Matériaux de Montpellier [ICGM ICMMM]
dc.contributor.authorTAILLADES-JACQUIN, Mélanie
hal.structure.identifierInstitut de Chimie de la Matière Condensée de Bordeaux [ICMCB]
dc.contributor.authorGRIMAUD, Alexis
hal.structure.identifierInstitut de Chimie de la Matière Condensée de Bordeaux [ICMCB]
dc.contributor.authorMAUVY, Fabrice
hal.structure.identifierCéramiques Techniques Industrielles [CTI]
dc.contributor.authorLOURADOUR, E.
hal.structure.identifierMarion Technologies
dc.contributor.authorSALMI, J.
dc.date.issued2014
dc.identifier.issn0378-7753
dc.description.abstractEnOne of the main target of the French ANR CONDOR (2009-2011) project coordinated by EDF-EIFER was the elaboration of proton conducting BaCe0,9Y0,1O3−δ-based cells using processes suitable at industrial level. Thus, commercial powders produced at kilogram scale (anode, electrolyte and cathode) have been analysed and used. Then, elaboration of protonic ceramic half-cells by co-pressing method from 25 mm to 80 mm in diameter has been assessed in order to establish the suitability of this shaping method regarding industrial requirements. According to results, the co-pressing method is relevant for the elaboration of cells up to 40 mm in diameter (laboratory experiment). A sintering step was carried out to densify the electrolyte layer to get a gas-tight membrane. Nickelate-based cathodes were screen-printed and electrochemical performances of the final assembly have been measured. Electrical power up to 180 mW cm−2 at 600 °C has been obtained on both 25 and 40 mm cells.
dc.language.isoen
dc.publisherElsevier
dc.subject.enPraseodymium nickelate
dc.subject.enYttrium-doped barium cerate
dc.subject.enCo-pressing
dc.subject.enScreen-printing
dc.subject.enUp-scaling
dc.subject.enProton ceramic fuel cell
dc.title.enEvaluation of proton conducting BCY10-based anode supported cells by co-pressing method: Up-scaling, performances and durability
dc.typeArticle de revue
dc.identifier.doi10.1016/j.jpowsour.2013.12.082
dc.subject.halChimie/Matériaux
dc.subject.halChimie/Autre
bordeaux.journalJournal of Power Sources
bordeaux.page302-307
bordeaux.volume255
bordeaux.peerReviewedoui
hal.identifierhal-00949313
hal.version1
hal.popularnon
hal.audienceInternationale
hal.origin.linkhttps://hal.archives-ouvertes.fr//hal-00949313v1
bordeaux.COinSctx_ver=Z39.88-2004&rft_val_fmt=info:ofi/fmt:kev:mtx:journal&rft.jtitle=Journal%20of%20Power%20Sources&rft.date=2014&rft.volume=255&rft.spage=302-307&rft.epage=302-307&rft.eissn=0378-7753&rft.issn=0378-7753&rft.au=DAILLY,%20Julian&MARRONY,%20Mathieu&TAILLADES,%20Gilles&TAILLADES-JACQUIN,%20M%C3%A9lanie&GRIMAUD,%20Alexis&rft.genre=article


Archivos en el ítem

ArchivosTamañoFormatoVer

No hay archivos asociados a este ítem.

Este ítem aparece en la(s) siguiente(s) colección(ones)

Mostrar el registro sencillo del ítem